If your Breezair evaporative cooler is overflowing, water is going in faster than it can get out. The usual culprits are a stuck float valve, a faulty water inlet valve, a drain valve that won’t close, or a blocked drain line. Turn off the water and power first, then work through the checks below.
Nothing spoils a Perth summer arvo like water pouring off the roof while your cooler runs. Overflow wastes water, stains your roof and eaves, and can eventually leak through your ceiling.
The good news is that most cases come down to a handful of causes. This guide covers all seven, how to spot each one, what you can safely check yourself, and when it’s time to call in a pro.
Why Is My Breezair Overflowing?
- Float valve stuck, jammed or out of adjustment
- Water inlet solenoid valve not sealing properly
- Drain valve or limit switch not closing
- Blocked drain or overflow lines
- Scale and debris stopping valves from sealing
- High water pressure pushing past the valve
- Clogged pads or water distribution sending water over the edges
Signs Your Breezair Is Overflowing
You’ll usually notice one of these:
- Water running down the roof or eaves
- Water pouring out of the overflow pipe
- The cooler still filling after you’ve switched it off
- A wet roof around the unit, or stains on the ceiling inside
What to Do Straight Away
- Turn off the water and power. Shut the isolation tap on the roof or near the unit, then switch the cooler off at the wall controller and the main switchboard.
- Have a safe look inside. If it’s dry and safe to get on the roof, open the side panels and check whether the float valve is jammed against the tank wall or needs adjusting.
- Know when to stop. If a quick clean and check doesn’t fix it, call a technician. Roof work gets risky around solar panels, wet surfaces and slippery tiles, and it’s not worth a fall.
7 Common Causes and Fixes of a Breezair Overflowing
1. Stuck or Misadjusted Float Valve
If the float ball or arm is jammed, set too high or has a worn seal, the water supply won’t shut off when the tank fills, so it spills over the edge.
This is the most common cause. With the water and power off, check that the float moves freely and isn’t touching the side of the tank.
If the water sits higher than the overflow outlet, adjust the float so it shuts off lower. If the seal is worn or cracked, adjusting won’t hold for long and the valve needs replacing. Once it’s sorted, turn the water back on and watch the cooler fill to make sure it cuts off at the right level.
2. Faulty Water Inlet (Solenoid) Valve
A solenoid valve that doesn’t seal fully keeps water streaming in even when the tank is full or the cooler is switched off.
The giveaway is water still flowing in after the cooler has shut down. Dirt, scale or a worn internal seal usually stops the valve closing. If the filling stops as soon as you close the isolation tap, that points straight at the valve.
Cleaning might buy you a bit of time, but a failing valve will let go again. Because a solenoid valve mixes electrics and water, replacing it is a job for a licensed technician, not a weekend DIY.
3. Drain Valve or Limit Switch Malfunction
If the drain valve or its limit switch sticks or doesn’t close properly, water drains or backs up when it shouldn’t.
Depending on your model, the cooler drains and refreshes the tank water automatically, so the drain valve gets a regular workout. When it sticks partly open, the cooler keeps draining and refilling, wasting water and sometimes overshooting the level.
A faulty limit switch can also give the wrong signal about whether the valve is open or closed. Listen for water running when the cooler should be idle. Both parts are best replaced by a technician.
4. Blocked Drains or Hoses
Kinked, clogged or scaled-up drain and overflow lines can’t carry water away, so it backs up into the tray and out the top.
Have a look along the full run. Check for kinks, crushed sections and gunk at the outlet, like leaves, grit or even a nest. Flush the line with clean water to clear loose debris, and avoid poking sharp objects down it, which can damage the pipe.
If the line is heavily scaled or you can’t clear it, a technician can sort it properly.
5. Scale, Minerals and Debris on Valve Seats
Limescale and grit on valve seats stop them closing fully, so a valve that isn’t actually broken can still let water through.
Perth water can be on the harder side, and bore water is often worse. Over a season, scale builds up on the float valve, inlet valve and drain seal. That’s often why overflow keeps coming back after a quick fix.
Turn everything off, clean the seats and seals, flush out the sump, and replace any parts that look pitted or worn. A clean at the start of summer helps stop it building up again.
6. Water Pressure That’s Too High
Strong mains pressure can force water past a valve seal that would normally hold, causing overflow even when the valve is working.
If your overflow comes and goes, or mostly happens overnight when household demand drops and pressure rises, this is a likely suspect. High pressure also wears out float and inlet valves faster.
A licensed plumber can check your pressure and fit or adjust a pressure-limiting valve. Changes to the water supply line should always be left to a licensed plumber.
7. Clogged Pads or Blocked Water Distribution
When pads are scaled up or distribution lines and troughs are blocked, water can’t flow through properly, so it spills over the pad frame and runs out of the unit.
With the power off, take a look at the pads. If they’re stiff, crusty or packed with scale, water will run off them instead of soaking through. Clear any debris from the water troughs and distribution tubes, and clean or replace tired pads.
It can look like a full-on cooler overflow, but the tank itself might be fine.
How to Tell Which Cause You’ve Got
| What you notice | Likely cause |
|---|---|
| Water keeps coming in with the cooler off | Inlet solenoid valve (2) or float valve (1) |
| Water running when the cooler should be idle | Drain valve or limit switch (3) |
| Water backs up and spills from the top | Blocked drain or overflow line (4) |
| Overflow returns after a quick fix | Scale and debris (5) |
| Overflow comes and goes, often overnight | High water pressure (6) |
| Water running over the pad frame | Clogged pads or distribution (7) |
When to Call a Perth Technician
Call in a pro if:
- The overflow returns after you’ve cleaned and adjusted the float
- You think the solenoid, drain valve or limit switch is the problem
- The roof is tiled, steep, wet or has solar panels in the way
- You can see water stains inside the house
Water and electricity don’t mix, and a bad fall costs a lot more than a service call. At Air Cool Care, we look after Breezair and other evaporative cooling systems across Perth, from Joondalup and Wanneroo down to Rockingham, Mandurah and Armadale.
We’ll find the cause, fix it and get your cooler running properly again.
Frequently Asked Questions About Evaporative Cooler in Perth
1. Is an overflowing evaporative cooler dangerous?
It can be. Water near your ceiling can reach lights, wiring and insulation, and a wet roof is slippery to work on.
If water is coming through the ceiling, switch the cooler off at the switchboard, keep clear of wet fittings and get a licensed electrician or technician to check it.
2. Will an overflowing Breezair push up my water bill?
Yes, it can. A valve that’s stuck open can keep water running for hours or days without you noticing, and you pay for every litre.
Spotting it early and fixing the cause is the best way to avoid a nasty surprise on your next Water Corporation bill.
3. How much does it cost to fix an overflowing Breezair in Perth?
It depends on your model and what’s failed. A float valve adjustment or clean is usually a smaller job than replacing a solenoid valve, drain valve or limit switch.
Ask for a quote that covers the call-out and parts before work starts, so there are no surprises.
4. How often should I service my Breezair in Perth?
Once a year is a good rule, ideally before summer kicks off. In Perth, a spring service lets a technician check the valves, pads, drains and float setting, and clean off scale, so problems get picked up before the first heatwave rather than during it.
5. Is it worth repairing an older Breezair that keeps overflowing?
It depends on the cooler’s age, condition and the repair needed. A single worn valve is usually worth fixing. If the unit is old, the cabinet is rusting through or several parts are failing at once, replacing may make more sense.
A technician can give you an honest comparison.
Conclusion
A Breezair that’s overflowing is almost always telling you one of seven things: the float or inlet valve isn’t shutting off, the drain isn’t working right, scale or pressure is getting in the way, or the pads and water distribution are blocked. Turn off the water and power, do the safe checks, and don’t leave it running, because even a small overflow wastes water and stains your roof. If it keeps coming back, get it looked at properly.
Air Cool Care is always happy to help.